Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

注射成形粘结NdFeB磁体:工艺·性能·应用

综合介绍了几种适于注射成形粘结NdFeB磁体的磁粉制备方法及特点；讨论了粘结剂、改性剂及磁场取向对注射成形NdFeB磁体最终磁性能的影响及其应用市场。在此基础上，指出了今后开展研究工作的方向。     

济钢高炉喷煤数学模型的研究与应用

基于湍流两相流理论建立了高炉喷煤两相流动及传质三维数学模型。采用该模型指导高炉生产 ,高炉利用系数由2 .7t/(m3.d)提高到 3 .0 t/(m3.d)以上 ,焦比由 460 kg/t降到 40 0 kg/t,煤比达到 10 0 kg/t,提高了高炉的各项经济技术指标。     

250W带功率因数校正整流电源模块的研制

功率因数校正技术越来越成为电源行业研究的热点。文中介绍了适用于雷达等设备的250W带功率因数校正整流电源模块的设计，分析了其中升压电感器设计、主开关管保护、控制电路消振、散热设计和表面贴装等关键技术，完成了实验研究，获得了满意的试验结果。     

Ability of a contactless inductive device for the characterization of the critical current versus temperature in superconducting rings at temperatures close to TC

Critical current measurements for three polycrystalline rings of YBCO, three Bi-2223, and one YBCO + Ag were developed from a temperature close to 80 K to the critical temperature using a previously reported contactless inductive device based on the transformer method. These data were used to analyze the ability of this device to characterize, in superconducting rings, the Ginzburg-Landau, Ambegaokar-Baratoff, and De Gennes regimes as well as the crossover temperature between them.     

Investigation on vapor-cooled current leads operating in a pulse mode

This paper describes transient numerical modeling for thermal characteristic of vapor-cooled current leads under pulse operation. The transient thermal analysis considers the temperature difference between a helium gas flow and a copper lead with temperature dependent properties of helium gas, copper and stainless steel. The numerical analysis was validated by an experiment with commercially available 100 A vapor-cooled current leads. A proper overloading factor calculation and the effect of intermediate cooling are presented for the current leads under pulse operation, which can significantly reduce heat input to a cryostat.     

高炉富氧鼓风的现状及机前供氧

阐述了高炉生产采用富氧大喷煤的必要性，国内高炉富氧鼓风的现状，以及机前富氧的优点和应采取的安全措施。     

流动注射分光光度法测定钴

研究了将ＰＡＮ用于流动注射（ＦＩＡ）分光光度法测定微量钴，在５６０ｎｍ处绘制标准曲线，线性范围为０～４５μｇ／ｍｌ，相关系数０．９９６，方法的相对标准偏差（ＲＳＤ）小于３％，加标回收率为９５％～１０５％，进样频率８０次／ｈ。本法简单快速，用于面粉、分子筛，铝合金测定结果令人满意。     

阳平关砂金矿精选厂尾矿综合回收的研究

本文详细的介绍了陕西省阳平关砂金矿精选厂尾矿金和其他可利用的矿物综合回收方法和最佳分选流程。     

我国清洁代用燃料汽车发展状况

随着汽车数量的迅速增加，汽车排放的有害废气也急剧增加，人们的健康受到威胁，解决这一问题的最好办法是发展清洁代用燃料汽车。介绍了天然气汽车和液化石油气汽车的主要优点，分析了目前我国清洁代用燃料汽车的发展现状，阐述了近期适宜发展我国清洁代用燃料汽车的机遇和面临的困难。最后就提高人们的环保意识、修改和完善汽车尾气污染控制法及排放标准、清洁代用燃料汽车的有关标准和安全措施。对发展这种汽车应给予优惠政策以及零部件生产和车辆改装企业的管理等方面，提出了建议。